Message on printer display
| | |
| The disk file system is full. | 1. Delete all unnecessary files from the EIO disk and then try again. Use HP Resource Manager to download or delete files and fonts. (See the software help for more information.) 2. Advise the customer to increase the permanent storage (use a larger EIO disk or add a RAM DIMM). |
| The flash DIMM had a critical or fatal failure. | 1. Reseat the flash DIMM and ensure it is locked into place. 2. Remove the flash DIMM and replace it with a new one. 3. The formatter could also be bad; replace formatter if needed. |
FLASH FILE OPERATION FAILED | The requested operation could not be performed (for example, attempting to download a file to a nonexistent directory). | 1. Check the file name and the directory name. 2. Reseat the flash DIMM. 3. Retry the operation. |
FLASH FILE SYSTEM IS FULL | The flash file system is full. | Delete unnecessary files from the flash DIMM and try again. Use HP Resource Manager to download or delete files and fonts. (See the software help for more information.) |
| The flash DIMM is protected and no new files can be written to it. | Disable the write protection through HP Resource Manager. |
HP TONER DETECTED alternates with PRESS GO TO CONTINUE | The printer has detected that the toner cartridge is not a genuine HP toner cartridge because it does not see or recognize the toner cartridge’s identification (model, manufacturing date, and serial number). | 1. Make sure the toner cartridge is a genuine HP toner cartridge. A non-HP toner cartridge will produce this error. Any printer repair required as a result of using non-HP toner is not covered under the printer warranty. 2. If the HP toner cartridge is new, the Elabel (cartridge memory) is missing or has been tampered with. 3. If the HP toner cartridge is used, the printer will not recognize the cartridge until 20 pages have been printed. After 20 pages have been printed, the error message disappears. 4. If the HP toner cartridge is used, and the error message remains after 20 pages have been printed, the cartridge has previously run out of toner. Replace the toner cartridge. |
INPUT DEVICE CONDITION [XX.YY] | An input paper-handling device has a condition that needs attention before printing can resume. 1st X = Device number in chain 2nd X= Device type (three types): 1 = Input 2 = Output 3 = Stapler/stacker unit YY = Device specific error | 1. Turn the printer off. 2. Disconnect the cable to the input paper handling devices and then reconnect it. 3. Ensure the device is properly connected and any doors or paper guides are properly closed. 4. Turn the printer on. 5. See the documentation that came with the paper-handling device for assistance. |
| The printer is unable to print the current job because the duplexer is not installed or not inserted correctly. | 1. Turn the printer power off. Install or reinsert the duplexer and ensure it is fully seated. 2. Ensure the right-angle power cord is used for the printer. |
| The toner cartridge has been removed and must be reinstalled for printing to continue. | Reinstall the toner cartridge and ensure it is fully seated. The high voltage power supply might also cause this error. |
| The printer is unable to print the current job because the specified tray [X] is open or not inserted correctly | 1. Reinsert the specified tray. 2. Check for damaged tabs on the right side of the tray. 3. Check for damaged tray sensor switches in the printer. 4. Replace the PCA controller in the feeder |
LOADING PROGRAM [NUMBER] alternates with DO NOT POWER OFF | Programs and fonts can be stored on the printer’s file system. At startup time, these entities are loaded into RAM. (These entities can take a long time to load into RAM depending on the size and number of entities being loaded.) The specifies a sequence number indicating the current program being loaded. | Available link for download
HP LASERJET 5200 ERROR 52 00 PAPER JAMMEDAnalisa sebelum di bongkar, printer ready begitu saya test print manual kertas narik sampai di tengah kertas berhenti bersamaan di layar error 52,00 nah setelah priksa sana sini saya temukan permasalahannya pada bagian scanner unitnya, lihat gambar di bawah ini. ternyata bagian scanner unitnya bersarang semut semut nakal dan beranak cucu di dalam. bersihkan semua dan pasang kembali ...wow,...sempurna..........sekian""""" Available link for download
HP LaserJet Error Messages A E
Message on printer display
| | | ACCESS DENIED MENUS LOCKED | The control panel function you are trying to use has been locked by the network administrator to prevent unauthorized access. | 1. Ask the network administrator to unlock the function. 2. Perform a cold reset. This will reset the printer to factory defaults. If a JetDirect network card is installed it will also reset the IP address and other settings so you might want to remove the JetDirect before performing the cold reset. | | The duplexer is not correctly installed. | 1. Some printers need a right-angle power cord for a duplexer to be installed correctly. Make sure right-angle cord is installed, if needed. 2. Turn the printer off. 3. Remove and reinstall the duplexer. 4. Turn the printer off and back on. 5. If the message persists, make sure the duplexer is connected and the connector is not damaged. 6. Replace the duplexer. | CHECK INPUT DEVICE alternates with PAPER PATH OPEN PLEASE CLOSE IT | The optional input tray cannot feed print media to the printer because a door or paper guide is open | 1. Check the doors and paper guides and close any that are open. 2. If doors and trays are closed, check tabs and sensor levers in the tray for proper operation. Replace any defective tabs or sensors. 3. Replace the PCA controller in the feeder. For 5si, 8000, 8100 series make sure C-link cable is correctly hooked up. Also on the 5si check the paper accessory PCA. | CHECK OUTPUT DEVICE alternates with CLOSE OUTPUT DELIVERY PATH | The optional output device is not properly connected to the printer. | 1. Ensure the optional output device is fully seated and properly installed. 2. Check any doors on the output device and verify they are closed. For 5si, 8000, 8100 series make sure C-link cable is correctly hooked up. | | The EIO disk had a critical failure or fatal error. | 1. Reseat the EIO disk. 2. Remove the EIO disk and replace it with a new one. 3. A bad formatter assembly could also cause this error, replace if needed. | DISK FILE OPERATION FAILED | Requested operation could not be performed (for example, attempting to download a file to a nonexistent directory). | 1. Check the file name and the directory name. 2. Reseat the EIO disk. 3. Retry the operation. | | The EIO disk is protected, and no new files can be written to it. | Disable the write protection through HP Resource Manager. | EIO DISK [x] NOT FUNCTIONAL | EIO disk is not working correctly | 1. Reseat the EIO disk in slot [X]. 2. Remove and replace the EIO disk in slot [X]. | ENV FEEDER LOAD [TYPE] [SIZE] | A job has been sent to the envelope feeder and the feeder is empty, the wrong size is loaded in the feeder, or the type and size are set incorrectly on the control panel. | 1. Load the requested envelope type and size into the envelope feeder. 2. Make sure the envelope size and type are set correctly from the paper-handling menu in the printer control panel. 3. Press GO if the desired envelope is already loaded in the feeder. 4. Press -VALUE+ to scroll through other available types and sizes. 5. Press SELECT to accept the alternate type or size. | ENVELOPE FEEDER SIZE = [xxxxx] | The printer is asking what size envelopes have been loaded in the envelope feeder. | In response, you can take either of the following actions: 1. Press SELECT to accept the current envelope size. 2. Press -VALUE+ to change the size and then press SELECT to accept the new size. If you do not press any buttons, the message disappears in about one minute. Note Changing the size here changes the default for the envelopefeeder size in the paper-handling menu. | ENVELOPE FEEDER TYPE = [xxxxx] | The printer has received a job under the following conditions: The envelope type the job requested is not available in the printer. Envelopes have been placed in the envelope feeder (thus triggering the paper sensor). | Available link for download
Read more »
IDM Error Cannot Transfer File di Windows 8salam, Entah apa yang salah atau memang tidak support, saya tidak berhasil mendownload file melalui Internet Download Manager (IDM). Padahal saya sudah melakukan Instalasi versi IDM dan browser yang up to date. namun setiap akan melakukan download selalu pesan error yang muncul. enteh IDM sudah tidak kompatible dengan Windows 8 saya juga kurang mengerti. akhirnya saya berfikir untuk menggunakan Download Manager Alternatif. Setelah saya coba akhirnya saya memutuskan menggunakan Free Download Manager. Interface yang similiar dengan IDM membuat saya tidak terlalu kesulitan menggunakan Download Manager ini. Selain itu software satu ini memiliki keunggulan ketimbang IDM yaitu - Proses download yang tidak mengganggu bandwith lain - Support Download torrent - Support Download Flash Content - Memiliki Preview
dan sejauh ini saya tidak menemukan error ketika melakukan download file dari internet. semoga bermanfaat
Download Available link for download
HP LaserJet Error Codes 20 49 Message on printer display | | | | | The printer received more data than can fit in available memory. | You may be trying to print a document that is too complex for the printers capacity (too many macros, soft fonts, or graphics). Pressing GO may print the transferred data, but data may be missing or skewed. If the file size of the print job exceeds printers onboard memory capacity, try adding more memory. Sometimes mismatched software drivers over-inflate the size of a document and cause these errors; you may want to download/install a different driver. If all else fails, simplify the print job and print manageable segments at a time. | | | The data (dense text, rules, raster or vector graphics) sent to the printer is too complex | Pressing GO may print the transferred data; but some data may be missing or skewed. More memory may help. You can also try a different driver, or simplify the print job by breaking it up into manageable segments. | 40 EIO x BAD TRANSMISSION | The connection has been broken between the printer and the EIO card in the specified slot. (Data loss might occur in this situation.) | 1. Press GO to clear the error message and continue printing. 2. Reseat the EIO card in slot corresponding to [X]. 3. Check cabling. 4. Replace the network card if needed. 5. Try a different software driver. | 41.3 UNEXPECTED PAPER SIZE |
The printer detected a media size different from what it was expecting. This is typically caused if two or more sheets stick together in the printer or if the tray is not properly adjusted. | 1. Reload the tray with the correct print media size. 2. Ensure that media in the tray is loaded under the front and back retaining tabs. 3. If you are printing from tray 1, verify that the correct paper size is selected in the control panel. 4. If you are printing from tray 2, 3, or 4, verify that any paper-size adjustments (length guide, width guide, size-selector switch) on the paper tray have been made correctly. Make sure the media is under the corner tabs. 5. After performing the actions above, press GO. The page containing the error will automatically be reprinted if jam recovery is enabled. (Or, you might want to press CANCEL JOB to clear the job from the printer’s memory.) For the 4000, 4050, and 4100 series the paper feed assembly could be bad. Also the paper feed/registration sensors could be knocked out of place. On EX engine printers this error is caused by a bad PIU (paper input unit).
| | | The media reached the PS102 or PS103 sensor too early. | 1. This error usually occurs with smooth media, such as transparencies or labels. If the problem persists when using tray 1, load media one sheet at a time. If the problem persists when using trays 3 and 4, replace the feed and separation rollers. 2. Check sensors PS102 and PS103 for proper operation. For the 4000, 4050, and 4100 series the paper feed assembly could be bad. Also the paper feed/registration sensors could be knocked out of place. On EX engine printers this error is caused by a bad PIU (paper input unit).
| | | A temporary printing error has occurred. | The page containing the error will automatically be reprinted. If the error persists: 1. Reseat the connections to the laser scanner and then to the engine controller board. 2. Replace the laser scanner. 3. Replace the engine controller board | | | A firmware error occurred | 1. Press CANCEL JOB to clear the print job from the printer memory. 2. Turn the printer off, and then turn the printer on. You can try reprinting the job to see if it was a temporary error. 3. If error persists, try printing a job from a different software application. If the alternate job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or certainprint job, try upgrading the printer driver and / or firmware.) 4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer. Turn the printer off and delete the print queue. Then reboot printer AND computer, reconnect cables, and try printing again. 6. Remove all EIO devices from the printer (JetDirect cards, hard drives, etc.). If 49 error goes away, turn printer off, re-install EIO devices one at a time, and reboot printer each time to determine which EIO device is failing. 7. If printing still fails with all EIO devices removed, remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM-- printer wont function without this installed.) Turn the printer on with DIMMS missing. If the error no longer exists, install each DIMM one at a time, turn printer on, test printer. Replace a DIMM if you determine that it causes the error. 8. Remember to reconnect all cables that connect the printer to the network or computer. 9. If the error persists, replace the firmware DIMM. 10. If error persists, replace the formatter. |
Sumber: http://www.printertechs.com
Available link for download
| |
Setelah cari cari kenapa masalahnya dari mbah google..memberikan pencerahan kurang lebih disebutkan permasalahannya pada bagian farmatter, dimana memory yang bermasalah, akhirnya ambil inisiatip sendiri dengan membersihkan bagian konektor dengan stip/penghapus pensil, alhasil setelah itu saya coba pasang kembali treng treng trengg,.....dek dek dek... akhirnya BERHASIL.
